3-piece Can Testing | Can making | Canneed Vietnam | Can need Vietnam | Pitesco Vietnam

     The CanNeed “Seam-X-On-Line X-Ray Automatic Seam Scanner” adopts non-destructive measurement method to measure the seam quality, suitable for measuring the aluminum cans, steel cans , aluminum-iron composite cans and etc. It’s applicable for online in producing department. It’s a non-destructive, cost saving, accurate measurement and automatic equipment which can be installed on the production line to improve the sampling frequency.

Advantages:
01)Non-destructive measurement, avoid wasting samples
02)Non-destructive measurement, avoid environmental pollution and save handling charges
03)High sampling frequency, reduce the isolation inferior
04)High sampling frequency, cost saving
05)Can track the chucks corresponding to the unqualified products
06)360-degree fully scan measurement
07)Can be suitable for various types of cans
08)Higher accuracy
09)Avoid manual measurement error
10)Durable
11)Accord with the worldwide safety standards

The CanNeed Seam Sight ® -B system can automatically collect the data from STG-200-d Seam Thickness Gauge and CSG-d Countersink Gauge. The actual seam thickness and countersink can be generated reports together with other data. To optimize the measurement process.

The CanNeed RPG-100 is able to scan profiles of seaming Rolls and Chucks (or other tooling - including carbide and ceramic tools) easily and quickly. The system can be used for acceptance testing for new seaming rolls or chucks, for quality assurance purposes and for stress analysis. Monitor tooling wear to replace rolls and chucks only when they need to be replaced

The CanNeed CAN-1050D Can Closing Force Gauge is for measuring the force of seaming head of the seaming machine. By using CAN-1050D, producers can avoid product defects caused by over plating: sharp edge, seam breakage, body deformation, body hook overlength, over large countersink and so on. In the meantime, producers can also avoid product defects caused by too small pallet lift force: slippery cans, too short hook and so on.

With the Mitutoyo 0.01mm resolution digital indicator. 
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.

IDG-100 is for small diameter cans, Cans dia. 52-100 mm (only measure one type can)
IDG-200 is for large diameter cans, Cans dia. :80-260 mm (only measure one type can)
IDG-300 is compatible for two (2) or three (3) sizes of cans.

The Canneed's “CTG-310 Coating Thickness Gauge” provides a computer enhanced method of rapidly assessing lacquer film weight of both internal and external coatings on beverage and food cans, and also tinplate.
Use standard coating plate (sample with known weight, g/m2) calibration equipment,to test different types of coatings.Test result and coating type number will display on the screen,and data output to PC with RS232.

The CanNeed “STG-200-D Seam thickness gauge (Digital)” is used to measure the Seam thickness of cans. With measure angle compensation. The center measure point can be adjusted. Cans can be auto-positioned in the center easily during measuring. With the Mitutoyo 0.01mm Resolution Digital Indicator.

The CanNeed DER-400 Digital Enamel Rater is the industry standard. The new CanNeed Enamel Rater DER-400 instrument test the coverage of the enamel coating inside food and beverage cans, aerosol-cans and also different kinds of ends. It displays an index of the amount of metal exposed by incomplete enamel coverage on a clear, easily read digital LED.

The CanNeed CND-TRK-300 Oven Temperature Trackeris a professional oven temperature curve inspection system for the coating industry, it is including the data logger, heat insulation case, software (Chinese / English) and thermocouples."CND-TRK-300 Oven Temperature Tracker" is use to pass through the oven with the solidifying products, and record down the real temperature during the process.

The canneed CLT-600 Leak Tester for can is used for checking the permeability of 3-piece cans in a water bath.
The can is fixed to magnet disc plate and submerged into the water. 
At the same time it is subjected to pressure and leaks are revealed by air bubbles. End and side seams visible.
A special parallel clamping system enables to measure different diameters and heights with one device. 
The clamping pressure and the test pressure may be set independantly.The operator determines the period of time the cans are under water. If he switches the by-pass lever and presses the two button valves, the cans deaerate and are lifted out of the water.
The whole test cycle is automated and is pneumatically controlled by pressure regulator valves.

The CanNeed “ZM-10 Digital Body Blank Gauge” is made for the quality control of can body blanks. It is a precision gauge for body blank measurement/angle measurement.

The Canneed "WWP-100 Welding Seam Ball Press Tester" is used to test the welding seam quality, including the welding seam strength and continuity of 3-piece cans. 

BDD-200A Bead Depth Gauge is the advanced model compare to the BDD-200, it is consisting of measuring units, digital indicator and data processor, operators only need to move the measuring needle to pass the beads, then the data processor will auto calculate and display the value of bead depth.

The CanNeed "DHG-300 Digital Can Height Gauge" can be used to measure the height of beverage, food, and aerosol cans. The gauges can be connected to a computer or SPC system via the adapter and cable.